Hot Tub ROUND 200 (Integrated Oven)

To ensure your hot tub is stable and secure, a solid base is essential. Although grass is an option, we recommend gravel or crushed stone as an ideal foundation.

It is especially important to keep an eye on the total weight of the hot tub, including water and people, if you want to place it on your terrace.

It is advisable to burn out the wood stove first, ie you should heat the stove once and let it burn for a while to remove all residues from the manufacturing process. Be careful, experience has shown that this will result in more smoke.

No, the hot tub is delivered almost fully assembled.
All you need to do is connect the hoses of the pre-assembled filter system and assemble the stainless steel chimney.

There are no assembly instructions for the hot tubs because each hot tub is delivered fully assembled. However, you will receive detailed, easy-to-read operating and maintenance instructions.

The smaller 180 hot tub has a capacity of 1200
liters, while the larger 200 hot tub can hold 1500 liters of water.

The good news: With proper care, the water can stay in the hot tub for months!

Water care is based on three pillars:
1. Filtration : The integrated filter continuously removes dirt particles, hair, and other impurities from the water. Run the filter pump for 2-3 hours per day.
2. UV disinfection : The UV lamp reliably kills germs, bacteria, and microorganisms without the need for harsh chemicals. It operates automatically during filter operation.
3. Maintenance products : Supplement the system with active oxygen or bromine. These products provide additional disinfection and keep the water crystal clear. Dosage according to the manufacturer's instructions.

Tip: Check the pH level weekly (ideally 7.0-7.4) and adjust it if necessary. With this maintenance routine, you can enjoy clean, hygienic water for months.

The wood stove needs about 1.5 - 2 hours to warm up (as a guideline), then the water in the hot tub is pleasantly warm (from 15°C to 37°C).

With a thermal lid, the water still has a temperature of about 30°C the next day.

The exact heating time depends, of course, on the size of the hot tub, the outside temperatures and the wood used.

For a hot tub with a wood-burning stove, you only need electrical connections for the lighting and the water circuit. A normal household connection with 230V is sufficient for this.

For a hot tub with an additional electric heater, you need an electrical connection with 440V (high voltage).

To prepare the electrical connection of the electric heater, you must first make sure that your fuse box provides the necessary connections.

Make sure you have a separate fuse for the 440V power connection required for the electric oven and a separate fuse for the 230V domestic connection required for the lighting and water circuit.

An electrician can help you to check the fuse box
prepare accordingly. When it comes to bringing high voltage electricity into the garden to your hot tub, it is advisable to seek professional help.

When it comes to laying high voltage current in the garden,
it is advisable to use an underground cable to ensure the power supply is safe and secure. Make sure that the cable is laid deep enough in the ground to avoid damage.

The power outputs of the individual electrical consumers are:

• LED lighting: 9W
• Filter system pump: 250W
• Pump for the 12 air jets: 700W
• Pump for the 8 water massage jets: 1,100W
• Pump for the 12 water massage jets: 2,200W

No, the wood of the hot tub cladding (spruce, thermo, larch, cedar) is oiled in the factory so that it is delivered impregnated.

Nevertheless, we recommend annual wood care for all types of wood, e.g. with the Remmers 3in1 glaze .

Option 1, most comfortable: You switch on the electric heater with a water temperature of 10°C, as frost protection.

Option 2, the most pragmatic: You run the filter pump 24/7, then the water is moved and moving water does not freeze.

Option 3, the most radical: You empty the hot tub.

To make the hot tub winter-proof, you do not need much
do.

First, drain the water from the hot tub, allowing the hot tub to drain as much as possible. Then, use a towel to wipe up any remaining sediment that cannot drain.

Once the water has been drained from the hot tub and the hot tub is empty, you can flush the water jets. To do this, run the water massage jets for 30 to 60 seconds to allow the pressure to blow any remaining water out of the jets and hoses.

The water that does not come out is so minimal that it cannot cause any damage to the pipes.

Then put the lid back on. On both sides,
To the right and left of the center, there is a removable element on the lid. These should be removed so that the hot tub can "breathe". Otherwise, condensation could form, which can lead to mold.

We accept all common payment methods in our shop such as PayPal, credit cards, Apple Pay and Google Pay, but also Klarna
Purchase on account and Klarna installment payments.

We can also arrange a payment plan, e.g. 50% deposit upon ordering and 50% upon delivery.

The delivery time for our Memelwood hot tubs is usually 4 - 6 weeks, depending on the order situation.

The hot tub is transported by a shipping company on a truck. The hot tub stands upright on the loading area.

The smaller 180cm hot tub weighs 200kg when assembled and the larger 200cm hot tub weighs 250kg. This means that four or five people can lift the hot tub and carry it to the installation site.

We offer you active and easily accessible customer support and will resolve the complaint together with you.

We know our suppliers well and are committed to ensuring that you receive the best quality or get help quickly.

You can contact us at any time, by email , WhatsApp or telephone .

In and of itself, by fully assembling the hot tub before transporting it to you, we ensure that the hot tub is complete and that all parts are correctly installed.

If something does happen, we offer active customer support. You can contact us at any time by email , WhatsApp or telephone .